How to Install a Ghost Immobiliser
Ghost immobilisers are hidden security device that protects your car from hacking and key cloning. It prevents the engine from starting until a PIN code is entered. It can be as long as 20 characters.
This extra layer of protection isn't visible to thieves who are unlikely to be aware of it. Some systems also have an app that allows owners to disarm the immobiliser in case they forget their PIN code, or to use a service/valet mode.
Connecting the vehicle's CAN Bus to the vehicle's
The Ghost 2 Immobiliser is a cutting-edge security system, is able to be integrated directly into the ECU of your vehicle. It is a subtle protection against thieves. It is extremely efficient and user-friendly. This makes it a valuable addition to your vehicle's security arsenal. Like all anti-theft devices, it's not foolproof and requires regular maintenance in order to function effectively. Luckily, this guide will help you get the most out of your Ghost 2 Immobiliser.
CAN (Controller Area Network) is a robust serial network that lets microcontrollers communicate with one another across short distances without the necessity of central control units. It is designed for multiplexing electrical wiring inside vehicles to reduce copper usage and comes with a variety of advantages, including low cost and a simple use.
The CAN protocol is used in most modern cars to communicate with the engine management system, transmission controller, steering control module, air conditioning controls, and more. It also carries sensor data including speed sensors and inputs, to control different features of the car. The CAN bus is able to monitor the health of these different components. It could stop the vehicle from starting when it is in a dangerous condition.
While the CAN bus can be used for a variety of purposes, it's crucial to know how it functions and how it's secured. It is possible to add additional features to a vehicle by using CAN bus, but it's crucial to safeguard it against threats from hackers and other types. The best way to accomplish this is to install firewalls and monitoring your CAN bus with software.
Ghost2's secluded control unit is hidden away in the car's wiring harness or dashboard, eliminating the possibility of a criminal physically altering it. It is impossible to reset a PIN code or emergency code without having access to the car.
You can activate Transport Mode when you have to sell your car to valet parking, service or for any other reason. This feature will disable both the keyfob and ignition functions of the Ghost immobiliser. It will only reactivate after the car has reached 31 mph for a time of 15 minutes.
How to create a PIN code
The Ghost immobiliser is a robust security device that shields your vehicle from theft. The revolutionary technology utilizes an PIN to shut down the vehicle's engine and prevent it from starting if you don't have the correct code, or an authorized fob or mobile. The system's subtle design ensures the system is not noticed and offers unbeatable protection against theft. Moreover, the system is TASSA verified and can provide significant savings on car insurance premiums.
During installation, Ghost enters a "learning mode" to record the sequence of buttons that are pressed to generate your unique pin codes. The installer will guide you through activating the system once the pin code has been created. Once activated the Ghost system will disable your vehicle's starting motor until you enter a valid PIN or switch the vehicle to transport mode. This makes it difficult for thieves or cloners to hack or duplicate the starter system of your vehicle.
Installing a Ghost immobiliser is easy but it is crucial to follow the precise instructions in the user guide to ensure proper operation. Hand tools are essential in making the perfect connections, and a multimeter can assist in determining electrical values. Insulation tape, heat shrink tubing and cable ties can be used to shield wires from damage. Check the system on a regularly basis to detect any potential issues.
Once the installation has been completed, it is important to make a final test of the system prior to turning on the ignition in your vehicle. Ghost immobilisers will re-arm themselves after 3 to 30 second dependent on the model of the vehicle. The system also comes with a Service/Valet Mode that lets you temporarily remove the system for servicing or valet parking.
Ideally, the immobiliser should be hidden in an inconspicuous location under the dashboard or steering wheel. It is recommended to use a small amount of duct tape or paint to mark the CAN H and CAN L wires so that you can easily locate them when you are testing. The CAN H and the L wires must also be connected to an electrical source that can provide a constant 12V. It is also essential to check the connections again after testing, as misidentifying these wires could cause the system to fail.
Activating the system
A ghost immobiliser stops your car from starting when you press a few buttons inside the vehicle, typically on the steering wheel, the door panel or the central console. The sequence can be changed by the user in case it is needed. Once the system is activated, it cannot be deactivated by thieves, making it a good option for anyone looking to safeguard their vehicle from theft.
The system is designed not to be able to be detected by modern diagnostic and code-grabbing technologies. It also doesn't broadcast out radio frequencies which makes it harder for thieves to detect the device.
If the device is located, it will stop the engine from starting. It will also sound an alarm to scare thieves away. The device can be used to monitor the location of a vehicle which can aid in the search for the vehicle in the event that it is stolen.
If you're interested in a ghost immobiliser get in touch with the experts at Car Specalist Customs to get a quote and discuss your options. We are fully qualified to install a ghost immobiliser for your vehicle and will make sure it is hidden in a remote area. We can also provide other security measures like the wheel lock and kill switch to help protect your vehicle from thieves.
Disarming the System
If you have a Ghost immobiliser that is fitted to your vehicle, it's essential to know how you can disable it. This will aid you in the event that you lock your keys inside the car or your battery fails. The system utilizes a unique PIN code, which only you know. It will not start the car without this code. The most efficient method of entering the code is to press a combination of buttons on your dashboard or steering wheel. This is much simpler than using a key fob. It also keeps others from copying the remote.
Ghost2 isn't intrusive unlike other immobilisers from the aftermarket which require cutting wires for installation. It also integrates with the CAN bus system of your vehicle to function. Its main feature is its ability bypass the engine without impacting your vehicle's normal functions, making it hard for thieves to make use of signal boosters or clone your car key. Moreover, it does not emit radio frequencies, meaning thieves aren't able to detect the system.
The Ghost system has the option of a Transport Mode that allows you to temporarily disable security for situations such as service or transportation. This feature is ideal for when you're loaning your vehicle out to someone else without sharing your PIN code, or if your vehicle needs to be kept secure while you drive it. To activate the Transport Mode, press the service button five times within 2 seconds. The Ghost system will confirm activation by giving five indication signals.
When you're done, remember to save the emergency code in a secure place away from your vehicle. If you are ever locked out of your vehicle You can call the technician or the company that installed the system, and they'll give you the code. If you are unable to reach them, then you can call an authorized dealer. However, this could require verification procedures and you may be charged for additional fees.
This system is not only useful, but it will also safeguard your vehicle from theft and reduce the cost of insurance. Numerous insurance companies offer reduced rates or financial incentives to install this system to prevent theft.